Search results for "flow [Keywords]"

Effect of stress and temperature on the thermomechanical degradation of a PE-LD/OMMT nanocomposites

2014

Thermomechanical degradation of nanocomposites is a topical issue that has not been fully investigated as demonstrated by the low number of papers available in the literature regarding this spe- cific aspect. In particular, with regards to low density polyethylene/clay nanocomposites, the degrada- tion behavior is very complex since it involves the degradation paths of both the polymer matrix and the organomodified nanoclay. In the present work, the effects of mechanical stress and temperature on the thermomechanical behavior of PE-LD/organomodified clay nanocomposites and the degradation paths were investigated by rheological, FT-IR and mechanical methods. The results have shown that the t…

Simulating Copolymeric Nanoparticle Assembly in the Co-solvent Method: How Mixing Rates Control Final Particle Sizes and Morphologies

2018

Abstract The self-assembly of copolymeric vesicles and micelles in micromixers is studied by External Potential Dynamics (EPD) simulations – a dynamic density functional approach that explicitly accounts for the polymer architecture both at the level of thermodynamics and dynamics. Specifically, we focus on the co-solvent method, where nanoparticle precipitation is triggered by mixing a poor co-solvent into a homogeneous copolymer solution in a micromixer. Experimentally, it has been reported that the flow rate in the micromixers influences the size of the resulting particles as well as their morphology: At small flow rates, vesicles dominate; with increasing flow rate, more and more micell…

Removal of TEX vapours from air in a peat biofilter: influence of inlet concentration and inlet load

2006

This paper presents the results of the study of the removal of toluene, ethylbenzene, and o-xylene (TEX) by biofiltration using a commercial peat as filter-bed material. Runs with a single organic compound in air, and with the mixture of TEX in air, were carried out for at least 55 days in laboratory-scale reactors inoculated with a conditioned culture. The influence of organic compound inlet load and of gas flow rate on the biofilter's performance was studied, including relatively high values of pollutant inlet concentration (up to 4.3 gC m−3 for ethylbenzene, 3.2 gC m−3 for toluene, and 2.7 gC m−3 for o-xylene). Results obtained show maximum elimination capacities of 65 gC m−3 h−1 for o-x…

Analysis of gate freeze-off time in injection molding

2004

Gate solidification time is an important topic in injection molding technology, as it determines cycle time, which itself is an important issue in the economics of the production process. In this work, a study of the effect of both gate and cavity geometries on gate solidification time was conducted, using a commercial polymer, injection molded with constant holding pressure into a rectangular cavity. Three cavity lengths were used, and for each, two cavity thicknesses were adopted. Spe- cial dies containing different gates were assembled in the mold. Gate thickness was found to be the most important factor determining gate sealing time. However, the cavity geometry is also quite important.…

Ozone absorption in aqueous phenol solutions

1977

Abstract The rate of ozone absorption in aqueous solutions of phenol was measured in a wetted-wall laboratory absorber. The liquid and gas flow rates were fixed as well as the pH and temperature. The phenol concentration was varied in the range 2–300 ppm and the ozone partial pressure over an eight fold range. The gas phase resistance to mass transfer was determined by absorbing SO2 from an SO2N2 mixture in KOH aqueous solutions. The results have been interpreted by means of a simple kinetic assumption.

Treatment of Combined Dairy and Domestic Wastewater with Constructed Wetland System in Sicily (Italy). Pollutant Removal Efficiency and Effect of Veg…

2021

Dairy wastewater (DWW) contains large amounts of mineral and organic compounds, which can accumulate in soil and water causing serious environmental pollution. A constructed wetland (CW) is a sustainable technology for the treatment of DWW in small-medium sized farms. This paper reports a two-year study on the performance of a pilot-scale horizontal subsurface flow system for DWW treatment in Sicily (Italy). The CW system covered a total surface area of 100 m2 and treated approximately 6 m3 per day of wastewater produced by a small dairy farm, subsequent to biological treatment. Removal efficiency (RE) of the system was calculated. The biomass production of two emergent macrophytes was dete…

Somatic embryogenesis and flow cytometric assessment of nuclear genetic stability for Sansevieria spp.: an approach for in vitro regeneration of orna…

2023

Sansevieria Thunb. species are traditionally known as succulent ornamental plants worldwide. They are also cultivated for medicinal, fodder, soil conservation and fiber uses, and for their capacity to reduce environmental pollution. Sansevieria sexual propagation is limited by the lack of viable seeds, and reproduction is largely made via vegetative propagation by suckers or cuttings. For these reasons, genetic improvement by conventional breeding is limited. To overcome this problem and to address the increasing demand from customers for novel Sansevieria varieties, many commercial companies regularly use in vitro propagation, as is the case in the breeding process of several ornamental pl…

Peak flow measurement in the Arno River by means of un steady-state water level data analysis

2008

Testing flow resistance equation for rill flow

2018

At first, in this paper a flow resistance equation for rill flow, deduced applying dimensional analysis and self-similarity theory, is presented. The incomplete self-similarity hypothesis is used for establishing the flow velocity distribution whose integration gives the theoretical expression of the Darcy-Weisbach friction factor. Then the deduced theoretical resistance equation, which is calibrated by some measurements of flow velocity, water depth, cross section area, wetted perimeter and bed slope carried out in 106 reaches of some rills modelled on an experimental plot, is tested using the literature data by Abrahams et al. (1996), Strohmeier et al. (2014) and Peng et al. (2015) for ri…

Effects of Boulder Arrangement on Flow Resistance Due to Macro-Scale Bed Roughness

2023

Flow resistance in gravel-bed channels is not only affected by the shape and size of the roughness elements, but also by their arrangement on the channel bed surface (position to flow streamlines, spacing between elements, and their protrusion from the channel bed). Many investigations proved that open channel flow resistance can be obtained by integrating the power velocity profile. For a macro-scale roughness condition, this study aims to investigate the effect of different boulder arrangements on flow resistance. First, for each arrangement, the equation relating Γ function of the power velocity profile, the Froude number, and the channel slope was calibrated using available measur…